To Assign DAC CC and Channel #s:
1. Find the DAC page in Edit Mode
(See “Navigating the Display in Edit Mode” above).
2. Select the Switch you want to edit. The Display will show the switch
number.
3. Press the ENTER/UNDO switch to underscore the editable field for
cc (Cc:xxx)and use the BANK UP/DOWN(+/-)switches to select the
3 digit cc# , or use direct number entry with the 10 numbered
switches, and always use leading zeros. Or press CLEAR/EDIT to
enter --- which means no cc# will be output for that switch. Once
you see the number you want, press the ENTER/UNDO switch to
store the change. The block cursor will now be displayed,allowing
you to leave the field or page.
4. Repeat #2 and #3 for each switch.
5. Use the same procedure as above to set the Channel # and LED
polarity (if necessary).
Assigning CC Pedals in Edit Mode
The RST has four CC pedal ports for connection of up to 4 passive controller pedals for effects parameter control. These ports
can be assigned globally: that is, the same cc and channel setting for all Banks/Presets or they each can be assigned to follow
both Preset A or Preset B commands. Both cc and channel #s are programmable. Any low impedance passive pedal can be
used. The pot value is optimal around 10K ohms, but most any low impedance pedal can be used. Pedals from Boss (FV500L)
and Mission (EP-1) are recommended. A TRS connection is required, with pedal “wiper” (or output) wired to RST Pedal port
“Ring”. RST Pedal port Tip connects to Pedal pot “high side” (or Pedal input) and Sleeve is common or ground.
To Assign CC Pedals:
1. Find the PEDAL page in Edit Mode
(See “Navigating the Display in Edit Mode” above).
2. Select the Pedal you want to edit via the Switches 1 thru 4. The
Display will show the switch number, and the respective switch
LED will be lit green.
3. Press the ENTER/UNDO switch to underscore the editable field
for cc (Cc:xxx)and use the BANK UP/DOWN(+/-)switches to
select the 3 digit cc#, or use direct number entry with the 10
numbered switches, and always use leading zeros. Or press
CLEAR/EDIT to enter --- which means no cc# will be output for
that pedal. Once you see the number you want, press the
ENTER/UNDO switch to store the change. The block cursor will
now be displayed,allowing you to leave the field or page.
4. Repeat #2 and #3 for each Pedal.
5. Use the same procedure as above to set the Channel # and
Assignment: either Global (Default), Preset A or Preset B.
Storing DAC Combinations in RST Bank/Preset A
This is the easy part. Once you have all your Preset A and DACs switches set up, just select the Bank/Preset, select the
combination of DAC switches you want on in that Bank/Preset, and press the STORE switch. Thats it. You can edit this
Preset combination at any time by selecting any of the DAC switches, either on or off.When the Preset is edited a “C” will
appear in the Display, indicating the Preset has been changed. If you like the change, press STORE. If you don’t like the
edited combination, press UNDO. The “C” will then disappear. Often you will make and store these Preset combinations first,
before going into Edit Mode and setting midi Program Change and cc pedal commands, but it is not mandatory you do so.
Note: If you are assigning cc Pedal commands per Preset, start from the Bank/Preset you
want to send from BEFORE entering the PEDALS page in Edit Mode
(87 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais